スケールアップおよび安全性の問題を明確化
OptiMax™ HFCalは、高い再現性で情報を提供しプロセスの特性評価およびスケールアップ検討を支援し、あらゆるスケールでの安全性確保を行います。
プロセスパラメータの理解
等温および非等温の両方の条件下で取得した熱データが、プロセスに類似した条件下でのプロセスパラメータの特性評価を可能にします。
シンプルで正確な熱量計
プラグアンドプレイの熱量測定モジュールにより、熱情報を正確かつ高精度に測定できます。
品番: 511628301
重量 | 35 kg |
使用容量 | 60 mL – 1,000 mL |
寸法 (高x幅x奥) | 78 cm x 39 cm x 42 cm |
温度範囲 | -40 °C – 180 °C |
バックライト/フロントライト | あり/あり |
ヒートトランスファ測定精度 | 通常 +/- 3% |
比熱測定の精度と正確さ | 通常 +/- 10% |
ヒートフロー精度 | 等温条件: ± 3 % から 5 % qcを含むqr_hf と、∫ qc を含む ∫qr_hf との比較に基づく 非等温条件: ± 5 % から 10% |
反応熱量測定方式 | ヒートフロー |
材質 | OptiMax スターターキット(51162830)およびアップグレードキット OptiMax HFCal(30050150) |
温度モード | ジャケット制御、リアクタ内温制御、還流モード、晶析モード |
加熱/冷却 | ソリッドステートサーモスタット |
電源 | 100 – 240 VAC, 50/60Hz |
迅速なプロセス開発
反応パラメータの特性評価と発熱情報の測定を同時に行います。発熱挙動とリアルタイム分析手法を組み合わせることで、安全なスケールアップのための情報を研究者に提供します。
正確な昇温と冷却
強力な昇温と強力な冷却を独自の制御アルゴリズムと組み合わせることで、急激な発熱反応が発生した場合でも温度を-40 °Cから180 °Cに正確かつ厳密に制御します。
正確なデータ分析
iControl ソフトウェアを使用すると、ワンクリックで伝熱係数、比熱、ヒートフローと反応エンタルピーを自動的に算出しレポート作成も可能です。
Thermostat | ||
Heating | Electrical | |
Cooling | Peltier | |
Cooling Performance | 0°C 35 W 20°C 65 W 40°C 95 W | |
Temperature Range | -40°C to 180°C (jacket temperature) | |
Control Modes | isothermal and isoperibolic, constant or ramp, reflux, distillation & crystallization | |
Stirring | 30 rpm to 1200 rpm | |
Dimensions | Thermostat: 388 mm x 414 mm x 539 mm | |
Power Supply | 100 V to 240 V AC, 50 Hz to 60 Hz, 1300 VA | |
Operation | iControl software for calorimetric applications Graphical touchscreen and/or iControl Software | |
Reactors | ||
Type | Single piece or two piece (with bottom drain valve) | |
Volume | 1000 mL | |
Pressure | 50 mbar to 1 bar | |
Material | Duran® glass | |
Stirrer | Pitch-blade (glass, Alloy 22) Anchor (glass, Alloy 22) Half-moon (PTFE for single piece reactor) | |
Calorimetry | ||
Type | Heat Flow | |
Calibration Heater | Max. 20 W | |
Precision Heat Transfer | Typically ± 3% | |
Accuracy and Precision Specific Heat | Typically ± 10% | |
Accuracy Heat Flow | Typically ± 3% to 5%, under isothermal conditions Typically ± 5% to 10%, under non-isothermal conditions | |
Sensitivity | ≤0.1 W measured as standard deviation of qr under steady state conditions. Peak-to-peak noise is ≤ approximately 0.4 W. | |
HFCal Module | ||
Power and Data Interface | Direct connection to CAN interface of standard OptiMax, no additional power supply or PC connection required | |
Data Logging | Via iControl Software | |
Dimensions | 120 mm x 40 mm x 170 mm | |
Software | iControl 5.2 or higher required, HFCal license |